Fulltext results:

450 4.3.2 Content Filter Timeout

3 Hits, Last modified: 7 years ago

ing** and check the ''Maximum Incoming Sessions'' value. Normally this should be about 20-30 * in VPOP3... lts** section. Especially check the response time value (especially the ''max success time'' value). If these are showing an error or are over a few hundred mil

SMTP error 'Invalid HELO name'

3 Hits, Last modified: 7 years ago

m'). Some SMTP servers don't bother checking this value because it has no authentication value at all, but a few do check that it looks correct. To correct thi... gs -> General and correct the **VPOP3 Host Name** value. See [[reference:misc_settings#vpop3_host_name|

Timeout while VPOP3DB is starting

3 Hits, Last modified: 7 years ago

left side of the window - Find the 'ImagePath' value on the right side of the window. - Edit the ImagePath value. If the end of the setting contains something like '-t 300', increase the 300 value (this is the time to wait in seconds, so maybe in

How to install PostgreSQL to use another port

2 Hits, Last modified: 7 years ago

P3\Database - Add/edit the PostGreSQLPort DWORD value to the new port number =====Create the VPOP3 use... s' (or use a different -U <username> and password value if you created a different superuser when setting

How to Obtain Error Logs

2 Hits, Last modified: 7 years ago

the maximum size of these files to an appropriate value (10MB is good for a busy VPOP3 installation) on t... size of the main VPOP3 log file to an appropriate value (10MB is good for a busy VPOP3 installation) usin

Repairing corrupted database

2 Hits, Last modified: 17 months ago

u get an 'unexpected chunk number error for toast value..' in the messages.msgdata table then this means ... ata and the 'toast' values, or within the 'toast' value itself has been damaged. A similar problem is an

VPOP3 Status Service Disabled

2 Hits, Last modified: 7 years ago

ber8** on the left. Then, on the right, check the value of the **Enabled** setting. If this is set to **0... opping the service), then, in RegEdit, change the value of the **Enabled** setting to **1** and [[start V

Alternative method of automatically starting VPOP3

1 Hits, Last modified: 7 years ago

ase the delay before VPOP3 starts, then alter the value after the '-n' line on the PING command in the ba

Data stream contained NUL character

1 Hits, Last modified: 7 years ago

on of the problem===== NUL characters (bytes with value 0) are not allowed in email messages and should n

Out of Disk Space When Sending Mail

1 Hits, Last modified: 7 years ago

ulSmith\VPOP3\Secret * Create or edit a DWORD value called CheckDiskSpace and set it to 0 (zero)

Outlook / Outlook Express is sending mail repeatedly

1 Hits, Last modified: 7 years ago

. -> Advanced**, and change the 'Server Timeouts' value. (For information, the SMTP standard ([[http://to

The message could not be loaded. Please return to the Quarantine page and try again

1 Hits, Last modified: 7 years ago

html?msgid=Q01d07d6106d1e384000002ed.dat&... The value after 'msgid=' (beginning with Q and ending with

How to move the VPOP3 Message Store to a new PC

1 Hits, Last modified: 7 years ago

r' to the IP address of the new PC, and clear the value of 'PostGreSQLHostName'. Restart VPOP3 and check

v3/4 - Move the message store to a new folder/drive

1 Hits, Last modified: 7 years ago

re\PaulSmith\VPOP3** and set the **MessageStore** value to point to the new location =====Restart VPOP3=

VPOP3 cannot access PostgreSQL - timeout expired

1 Hits, Last modified: 7 years ago

(the password is 'pgsqlpass') If the displayed value is over about 100,000, then this may be the probl

Error message: Your connection has been blocked temporarily - Try again later

1 Hits, Last modified: 7 years ago