PSCS Wiki

Temporary Files

Anonymous (anonymous@undisclosed.example.com) — 2026-05-13T14:03:39+00:00

Temporary Files This is for files in the VPOP3\_temp folder Most of the filename is the hexadecimal timestamp (in Windows 'FILETIME'/65536 form) with a 4 digit hex sequential number afterwards. The first letter or two (usually G-Z) can tell something about what caused the file.

We installed a new router and now nothing works

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

We installed a new router and now nothing works If you installed a new router on your network and left it at the default settings, you may find that VPOP3 doesn't seem to work afterwards. This is because it may be that the new router allocates new IP addresses on your network.

550 5.7.1 Relaying not allowed! Bad sender IP address

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

550 5.7.1 Relaying not allowed! Bad sender IP address This SMTP error message means that the computer which is sending the message is not permitted to send outgoing messages based on the VPOP3 SMTP Service's Access Restrictions. This is probably because someone is trying to send messages from outside your local network, and you have not configured VPOP3 to allow this. You have to be careful when allowing this, because you may configure VPOP3 to be an open-relay, which is a

How To Setup VPOP3 Service Security

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

How To Setup VPOP3 Service Security VPOP3 can be configured to restrict access to its various services depending on the client computer's IP address. This is useful if you want to allow access from only certain IP addresses (eg within your LAN) and prevent access from other IP addresses (eg the Internet).

Autoresponder Commands

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Autoresponder Commands This article only applies to VPOP3 v4 and earlier A VPOP3 autoresponder can contain special text strings to create special behaviour, in addition to plain text as part of the response. There are three types of 'command' *

VPOP3 Server Access Not Allowed

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

VPOP3 Server Access Not Allowed If you get an error like: -ERR VPOP3 Server access not allowed! when trying to access VPOP3, then this means that the relevant server's IP Access Restrictions defined in VPOP3 do not allow access from your client computer.

Incoming SMTP Feed

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Incoming SMTP Feed An incoming SMTP feed is where incoming mail is sent directly to your mail server without going through your ISP's POP3 mail server on the way. Advantages An incoming SMTP feed has several advantages over going via a POP3 mailbox:

Timeout problems downloading/uploading messages with attachments

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Timeout problems downloading/uploading messages with attachments There are various possible reasons for this, usually to do with third party internet security software but they may also be associated with Windows TCP/IP or dial-up adapter issues. You may not have problems with other software, but that doesn't mean the problem is being caused by VPOP3.

How To Allow Mail Relay Through VPOP3

Anonymous (anonymous@undisclosed.example.com) — 2025-05-21T07:57:18+00:00

How To Allow Mail Relay Through VPOP3 If you are allowing remote access into VPOP3 to collect mail then you may also want those remote users to be able to send their outgoing mail through VPOP3 as well. This is more complex than allowing users to collect mail, because, by default, SMTP connections are not authenticated. This means that when someone tries to send a message through VPOP3, VPOP3 doesn't know who that user is. This can cause a problem if unauthorised users try to send mail through…

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

The ping command is a useful way of diagnosing network problems. It's similar to the sonar ping in a submarine. It sends out a signal to a specified machine and waits for a response to be echoed back. * Open a command prompt * Type ping www.pscs.co.uk. You should see a display like this:

RBL Checking not working in VPOP3 Enterprise

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

RBL Checking not working in VPOP3 Enterprise VPOP3 Enterprise has an RBL checking feature which is configured in the VPOP3 Settings at Services -> SMTP Server -> SPAM Reduction -> Realtime Blacklist Rules If it does not seem to be working properly, there are a few reasons why the RBL feature may not work.

Remote Access to VPOP3 without a permanent Internet connection

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Remote Access to VPOP3 without a permanent Internet connection If you do not have a permanent connection to the Internet, then the user will need to dial directly into the VPOP3 computer or another computer on the network. This only works reliably if the dial-inserver is running Windows NT, Windows 2000 or later versions.

Which versions of Windows will VPOP3 run on?

Anonymous (anonymous@undisclosed.example.com) — 2026-03-18T20:53:41+00:00

Which versions of Windows will VPOP3 run on? (Note - no version of VPOP3 will run on “Windows 10 S”) Version 9.0 or later VPOP3 version 9.0 or later requires Windows 8.1/2012R2 later. It needs a 64 bit version of Windows. Version 8.0 or later VPOP3 version 8.0 or later requires Windows 7/2008R2 SP1 or later. It should run on both 32 bit and 64 bit Windows.

Allow Remote Access to VPOP3 Mailboxes

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Allow Remote Access to VPOP3 Mailboxes Sometimes people want to be able to access their office VPOP3 mail server from a remote site or mobile phone etc. These instructions assume you have a permanent Internet connection (eg ADSL, Cable etc). If you don't have a permanent Internet connection, see

PostgreSQL Replication

Anonymous (anonymous@undisclosed.example.com) — 2019-02-06T17:10:31+00:00

PostgreSQL Replication PostgreSQL 9.1 (used in VPOP3 5 and later) supports replication from a 'Master' to a 'Slave' database server. This can be used with VPOP3 for having a near-realtime backup of your settings & messages. To use the replication, you need to have a file share which is accessible from both PCs. The thing to watch out for is that the PostgreSQL services may be running as a different user from the currently logged in user, so make sure that the user(s) which the PostgreSQL servi…

Some PCs cannot access VPOP3 when VPOP3 is connected to the Internet

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Some PCs cannot access VPOP3 when VPOP3 is connected to the Internet This error happens when you have multiple TCP/IP subnets on your network. The computers which are on different subnets from the VPOP3 computer will not be able to see VPOP3 whilst VPOP3 is connected to the Internet (through a dial-up connection). Whenever VPOP3 is offline, it will work correctly.

VPOP3 Is Responding Slowly

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

VPOP3 Is Responding Slowly If VPOP3 is responding slowly to users there are several common causes: * The VPOP3 server disk may be badly fragmented. Defragment the server disk(s). Note that sometimes the Windows defragmenter will say that the disk doesn't need defragmenting even if it does, so it is best to do it anyway. Also, there is a better free defragmenter available called

Connections

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Connections In VPOP3 a Connection tells VPOP3 how to 'connect' to the Internet. VPOP3 supports up to 10 Connections, which can be either network connections or Dial-Up connections (using a modem) A Connection is linked to one Mail Sender and zero or more Mail Collectors.

Dynamic IP Address

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Dynamic IP Address VPOP3 needs to run on a computer with a static (fixed) IP address on the 'local network'. This does not mean that it will not work with ISPs that dynamically assign IP addresses! A computer which has both a LAN adapter AND a dial-up adapter will have two IP addresses: one for the

Socket Error 10060 - Operation Timed Out

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Socket Error 10060 - Operation Timed Out This error is quite self explanatory. It means that Windows reported that a connection attempt or idle connection timed out. If this error occurs during a connection attempt (eg in a VPOP3 - SMTP Client connection problem error message), then it means that Windows couldn't connect to the ISP mail server within a fixed time (the timeout limit is fixed within Windows itself). This problem can either mean that your ISP is having a problem, that you are con…

Archiving not saving messages on a shared drive

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Archiving not saving messages on a shared drive If the VPOP3 archive facility is reporting “Possible error accessing main store directory” and the archive store directory is a drive on another network computer, then there are a few possible difficulties that you have to be aware of.

Exchange 2007

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Exchange 2007 You can link VPOP3 to Exchange Server, so that Exchange Server sends outgoing mail through VPOP3 and VPOP3 sends any incoming mail directly to Exchange Server. You should first of all set up VPOP3 to send and receive Internet email as normal.

Initial Configuration Tasks

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Initial Configuration Tasks After installing VPOP3, you will need to get into the VPOP3 settings. The easiest way of doing this is to find the VPOP3 Status Monitor in the Windows task tray. Right-click this icon, and choose 'VPOP3 Settings'. (If that doesn't work, see this article to troubleshoot Status Monitor problems). Alternatively, on the VPOP3 PC, you can go to Start

"How To" Articles

Anonymous (anonymous@undisclosed.example.com) — 2026-03-18T20:20:50+00:00

"How To" Articles Installation/Upgrades * Download VPOP3 * Install VPOP3 * Move VPOP3 * Upgrade VPOP3 * Upgrade VPOP3 to version 5.x or 6.x from version 4 or earlier * Upgrade VPOP3 to version 7.x from version 6 or earlier * Upgrade VPOP3 to version 8.x from version 7 or earlier * Upgrade VPOP3 to version 9 or later from version 7 or 8 * Performance Requirements * Installation Checklist General Configuration * Initial Configuration * Users * Add an Alias * Create…

Require SMTP Authentication

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Require SMTP Authentication There are some situations where VPOP3 needs to know who is sending mail. This may be if you have VPOP3 configured to behave differently depending on who is sending messages - eg if you have different message size limits depending on the sender, or if you have message monitoring configured for certain users, or you don't want certain people to be able to send mail at all.

How to move the VPOP3 Message Store to a new PC

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

How to move the VPOP3 Message Store to a new PC Use this option if you want to have VPOP3 running on one PC, but have the message store database on another PC. Manually Install PostgreSQL on the new PC Download the 'pgInstaller' version of PostgreSQL from the

Move VPOP3 Version 5 (or later) to a new PC

Anonymous (anonymous@undisclosed.example.com) — 2026-04-21T11:12:40+00:00

Move VPOP3 Version 5 (or later) to a new PC Moving VPOP3 Version 5 or later to a new PC is slightly different from moving earlier versions, because of the database system, which was introduced for version 3 and modified for version 5. The summary of steps is: * Stop VPOP3 on the original PC

Settings -> Attachment Processing

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Settings -> Attachment Processing The Attachment Processing page allows you to configure VPOP3 to perform two distinct functions on messages that contain attachments: * * Filtering The Filtering tab is divided into four main sections: Attachment Filtering

Route incoming POP3 mail by parsing message headers

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Route incoming POP3 mail by parsing message headers This routing method is generally used if you have a catch-all or 'multi-catch' mailbox with your Internet provider. With this method, VPOP3 will look at the To/Cc and other fields in the message headers to try to work out who the message is for. If the recipient is not listed in the headers (eg for BCCd mail) it may not be able to automatically detect who the message is for.

SMTP -> General tab

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

SMTP -> General tab This page is reached from Services -> SMTP Server, then the General tab. This page lets you set general settings for the SMTP service component of VPOP3. The SMTP service is how users send outgoing mail, and how incoming SMTP messages arrive. Service Name

UserRuleConditions Replacement

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

UserRuleConditions Replacement Use: ~userruleconditions~ ~end~ Required parameter: Account, RuleId This returns the message rule conditions for the specified rule The format string can have the replacements * id - numeric ID of the condition

Socket Error 10054 - The virtual circuit was reset by the remote end

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Socket Error 10054 - The virtual circuit was reset by the remote end Error 10054 means that the connection between VPOP3 and a remote computer (eg the ISP or another computer on your LAN) was disconnected by something outside of VPOP3. This is often caused by anti-virus software or Internet security/firewall on the VPOP3 machine but it could be any of a number of things. Any software or hardware that is sitting between VPOP3 and the ISP could be the root cause.

Backscatter

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Backscatter In email, “backscatter” is the term used if you send bounce messages back to spam messages. As most spam messages use forged email addresses, then the bounce messages will go to an innocent person, who will find them very annoying. Stopping VPOP3 from sending Backscatter

Configuring Calendar on iOS

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Configuring Calendar on iOS These instructions are for configuring a new Calendar account on iOS for iPhone, iPad and iPod Touch. The version of iOS used for these instructions is iOS v6.0, but they will probably work or help with other versions of iOS.

Accepting Incoming SMTP through a router

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Accepting Incoming SMTP through a router If your ISP is providing you with an SMTP mail feed (incoming SMTP) and you have VPOP3 connecting to the ISP through a router then you will probably need to modify the router configuration to allow this. Most routers' default configuration will only allow outbound connections (ie connections from the local network out to the Internet). If you need to accept incoming SMTP mail, then you need to tell the router to allow inbound connections on port 25 for …

Data stream contained NUL character

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Data stream contained NUL character Description of the problem NUL characters (bytes with value 0) are not allowed in email messages and should not be transmitted over POP3, SMTP or IMAP4 except in certain circumstances. If an attachment contains such a byte it must be encoded using

Setting up VPOP3 to work with Exchange 2003

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Setting up VPOP3 to work with Exchange 2003 The instructions below are for Exchange Server 2003. For other versions of Exchange see here. You can link VPOP3 to Exchange Server, so that Exchange Server sends outgoing mail through VPOP3 and VPOP3 sends any incoming mail directly to Exchange Server.

How to upgrade VPOP3 to version 7 or later from version 6 or earlier

Anonymous (anonymous@undisclosed.example.com) — 2020-06-29T10:43:58+00:00

How to upgrade VPOP3 to version 7 or later from version 6 or earlier As usual the process to upgrade is simply to install the later version over your existing installation (do not uninstall anything first). The below is technical information detailing an extra step performed by the installer in this particular upgrade step.

Move VPOP3 Version 3 or 4 to a new PC

Anonymous (anonymous@undisclosed.example.com) — 2019-11-12T16:09:08+00:00

Move VPOP3 Version 3 or 4 to a new PC Moving VPOP3 Version 3 or 4 to a new PC is slightly different from moving earlier versions, because of the database system. The summary of steps is: * Stop VPOP3 on the original PC * Manually make a backup of the database on the original PC

VPOP3 Not Starting Properly

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

VPOP3 Not Starting Properly If VPOP3 is not starting properly, then the first thing to check is whether the database server is starting. In VPOP3 v3 and later, VPOP3 uses a PostgreSQL Database server for data storage, so if the database server is not running, VPOP3 will not be able to start properly. In this case, the VPOP3.EXE process may appear in Task Manager, but it won't respond to anything, or it may appear in Task Manager and then stop after a short period.

SMTP Relay Protection in VPOP3

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

SMTP Relay Protection in VPOP3 SMTP Relay Protection should be used on ALL SMTP mail servers (such as VPOP3) which have a permanent connection to the Internet. You may also want to use it on servers which are only connected occasionally via a dial-up connection.

Error message: Your connection has been blocked temporarily - Try again later

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Error message: Your connection has been blocked temporarily - Try again later If you get an error message in your email client software saying Your connection has been blocked temporarily - Try again later or Server access temporarily blocked! Please try again later

UserRuleConditions Replacement

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

UserRuleConditions Replacement Use: ~userruleconditions~ ~end~ Required parameter: RuleId This returns the message rule conditions for the specified rule The format string can have the replacements * id - numeric ID of the condition * field - field/data to test

Database -> Backups Tab

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Database -> Backups Tab The Backups tab lets you specify how VPOP3 will make its daily backup of its database. We strongly recommend that you backup the database regularly in case of disk problems or file corruption. You can use the VPOP3 backup feature, or manually backup the PostgreSQL database using the pg_dump command, or use another program to backup the PostgreSQL database if you wish. Note that a simple disk copy will

LAN Forwarding

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

LAN Forwarding LAN Forwarding is a feature of VPOP3 where it can send messages to another mail server using SMTP. This other mail server is usually on your local network (LAN), hence the name, but it can actually be anywhere that has a permanent network connection to VPOP3. VPOP3 will send messages using

Misc Settings

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Misc Settings This page contains some settings for VPOP3 which there is no other obvious place for them to go. * General Tab * DNS Tab * Disk/Memory Checking Tab * External Fax Tab * BATV Tab * Proxy Tab * Advanced Tab * Network Tab * Bandwidth Pools

POP3 Mail Collection

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

POP3 Mail Collection POP3 Mail Collection is when VPOP3 will collect mail from an external POP3 mailbox - for instance, from an Internet Provider. POP3 General This page tells VPOP3 how to collect mail. * POP3 Server Address - this is the name (or IP address) of the POP3 server from which you want VPOP3 to collect mail

Security Settings -> Intrusion Protection Tab

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Security Settings -> Intrusion Protection Tab Settings -> Security Settings -> Intrusion Protection Tab Starting in VPOP3 v6.0, VPOP3 can monitor failed logins for all accounts across all services and block an attacker's IP address from accessing VPOP3 for a specified time

Mail Connectors -> Mail Senders -> SMTP Direct

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Mail Connectors -> Mail Senders -> SMTP Direct VPOP3 can be configured to send mail directly to the recipient's mail server (or the recipient's mail service provider). Usually this is only used if you have a high-end business class Internet connection - such as a leased line, or your mail server is co-located in a data centre. Attempts to use SMTP Direct sending on a dial-up/ADSL/Cable/FTTC/etc connection may be problematic since the receiving mail server may think you a home user who has been …

SMTP Server -> IDS/IPS

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

SMTP Server -> IDS/IPS The IDS/IPS tab lets you set logging and automatic blocking parameters for the IDS (Intrusion Detection System) and IPS (Intrusion Prevention System) component of the SMTP server. SMTP servers are regularly attacked, both by incoming mail attacks (spam/viruses etc) and relay attacks (by spammers and other malware distributors trying to send mail through them). Because of this, there is a system in VPOP3 which will track attack attempts on the SMTP service and can automat…

Status

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Status The VPOP3 Status screen has two tabs * Server Status * Sessions Server Status The Server Status tab is essentially a copy of the VPOP3 Status Monitor information. * Connection Status - this shows the 'online' status of VPOP3. If it says idle, it does not mean VPOP3 is not working, or not doing anything, it just means that it is not currently sending or collecting mail from the Internet.

What's new in version 5 webmail?

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

What's new in version 5 webmail? This is a list of some of the most noticeable changes to VPOP3's webmail interface for version 5. For a more detailed list of changes, view our bugtracker. [VPOP3 Version 5 - mobile compatible webmail] Mobile compatible webmail If you access version 5 webmail from a mobile device, you will probably be redirected to the mobile compatible version. It is a cut-down version of Webmail, which retains the key features, but doesn't utilise the extra features which w…

Formatting Syntax

Anonymous (anonymous@undisclosed.example.com) — 2026-03-16T16:00:10+00:00

Formatting Syntax DokuWiki supports some simple markup language, which tries to make the datafiles to be as readable as possible. This page contains all possible syntax you may use when editing the pages. Simply have a look at the source of this page by pressing

VPOP3 Wiki

Anonymous (anonymous@undisclosed.example.com) — 2022-10-01T11:36:44+00:00

VPOP3 Wiki Welcome to the VPOP3 Wiki. Here you will find VPOP3 documentation, FAQs and “How To” articles * FAQs * How Tos / Troubleshooting * Reference * Tips & Tricks If you want to add information, hints & tips, etc, you can register on this Wiki and modify or create new pages. Please don't ask questions on the Wiki; if you have a question, ask it on

DNSSEC

Anonymous (anonymous@undisclosed.example.com) — 2019-09-19T13:41:29+00:00

DNSSEC DNSSEC (Domain Name System Security Extensions) is used to secure DNS records and prevent them from man-in-the-middle attacks and spoofing. DNSSEC has been around for 10 years, but it has generally not been widely adopted for various reasons, but it is

GDPR for other hosting services (eg web hosting)

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

GDPR for other hosting services (eg web hosting) As a hosted service provider, we are classed as a “Data Processor” under the GDPR regulations. For our hosting services: * Data is held in the UK. Data is not transmitted outside of the EU except at your explicit request or command.

How do I write an email to technical support?

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

How do I write an email to technical support? Please send the email to support@pscs.co.uk Note that free technical support is currently only available for version 3.0 and later When sending the email, please make sure you include all relevant information:

What is PostgreSQL?

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

What is PostgreSQL? PostgreSQL is an SQL database engine. VPOP3 and PostgreSQL In VPOP3 2.x, VPOP3 uses a database engine called SQLite for its database needs. SQLite has limited locking facilities, so on busy systems we encountered problems where databases would need very frequent updates, and the lock limitations would cause the updates to take a long time. For this reason we added optional support for PostgreSQL to later versions of VPOP3 2.x.

What is Webmail?

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

What is Webmail? “Webmail” is a term used to describe an email client which is accessed through a web page rather than as a standalone program. Some well known services which offer webmail are services such as Hotmail, Yahoo, Gmail etc. All versions of VPOP3 have a Webmail service included as standard.

1069 or 7000 Login Failure error when starting VPOP3DB service

Anonymous (anonymous@undisclosed.example.com) — 2019-11-13T15:35:55+00:00

1069 or 7000 Login Failure error when starting VPOP3DB service A 1069 or 7000 login failure error when starting the VPOP3DB service usually means that something is 'wrong' with the vpop3postgres account in Windows - the password may have expired, or someone may have reset the password.

Socket Error 10503 - No More Data

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Socket Error 10503 - No More Data Error 10503 means that the connection between VPOP3 and a remote computer (normally your ISP) was dropped at an unexpected time. This is different from the error 10054 in that this is a controlled line drop. One way this can happen is if the ISP's POP3 server uses an obsolete standard which allows it to drop the connection if a POP3 'LIST' command is performed on an empty mailbox. The current standard requires that the connection is not dropped until the clien…

Socket Error 11001 - Host not found (authoritative answer)

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Socket Error 11001 - Host not found (authoritative answer) This means that the ISP POP3 or SMTP server which you have told VPOP3 to connect to does not currently exist. This might be that you have mistyped the server address, or that your ISP is having temporary problems, or that you are using an internal

Alternative method of automatically starting VPOP3

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Alternative method of automatically starting VPOP3 VPOP3 usually automatically starts as a Windows service. Sometimes this does not work, either because other services need to start first, or Windows is going very slowly at startup, causing the database service to time out, or there are certain database control files which did not get cleared after a previous Windows shutdown.

Attachments have been removed or renamed

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Attachments have been removed or renamed If you have received an email and one or more of its attachments have been removed or renamed, it might be a result of Attachment Filtering. You can inspect the filtering rules by going to Administration Settings -> Settings ->

Autoresponders / Out of Office

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Autoresponders / Out of Office VPOP3 has an autoresponder facility for sending automatic replies when a message arrives in a mailbox. This is often used for 'Out of Office' replies, but it is not limited to that use. To set an autoresponder, the administrator can edit the user and go to the

Calendars in Mozilla Thunderbird

Anonymous (anonymous@undisclosed.example.com) — 2022-01-26T10:47:35+00:00

Calendars in Mozilla Thunderbird The Thunderbird email client supports CalDAV calendars as standard. This can be used to access VPOP3's CalDAV server. To add a VPOP3 CalDAV calendar to Mozilla Thunderbirdis straightforward * Add the calendar to Thunderbird

How to Create a Connection

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

How to Create a Connection There are two ways that VPOP3 can be configured to connect to the Internet. Which one you use depends on the service provided by your ISP. Using a Permanent 'Always On' Connection This is the most common connection method. It assumes you are connecting to the Internet via a router which is permanently connected. In this scenario VPOP3 simply needs to connect to the router so setting up VPOP3 is very simple.

How to create an SSL Certificate

Anonymous (anonymous@undisclosed.example.com) — 2026-03-23T10:18:43+00:00

How to create an SSL Certificate VPOP3 Enterprise supports SSL certificates for encrypted sessions. The basic mechanism to create an SSL certificate is that you have to generate a CSR (Certificate Signing Request) then send that to a CA (Certificate Authority) who will sign your certificate and give you the certificate back.

Daily Summary is not reporting all Sent messages

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Daily Summary is not reporting all Sent messages For VPOP3 to log outbound messages it needs to be able to work out that the message is FROM: a user whose mail is handled by the local VPOP3. To do this it has to examine the FROM: address in the message header.

Delete OutQueue messages directly from the database

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Delete OutQueue messages directly from the database If there is an extremely large number of messages (eg hundreds of thousands) in the VPOP3 OutQueue, then it may take a very long time for VPOP3 v5 and later to start as it check the message database tables for consistency during initialisation.

Find the IP address of the VPOP3 Computer

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Find the IP address of the VPOP3 Computer To find the IP address of the VPOP3 computer, in Windows go to Control Panel -> Network and Sharing Center. Press the Local Area Connection link Then press 'Details'. Look for the 'IPv4 Address' setting.

Forwarded Emails Not Arriving

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Forwarded Emails Not Arriving If you are having problems having VPOP3 forward incoming messages to an external address, but sending messages directly to that address works OK, and forwarding internal messages to that address works OK, then the problem may be the SMTP return address which VPOP3 is using.

Full Text Search

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Full Text Search In VPOP3 Enterprise v7.0 a facility for full-text-search on message content was added. Because the full-text-search indexes can be quite big, this facility is optional. For several reasons, the full-text-search is stored in a separate PostgreSQL database. This means that it is not backed up with your standard backups. After a restore, the full-text-search index can be rebuilt from the raw message content.

Handling mail for multiple incoming domains

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Handling mail for multiple incoming domains VPOP3 can easily handle mail for several incoming domains. Exactly how you do it depends on the exact situation. All domains are 'aliases' If the domains are aliases of each other, for instance, you have 'mycompany.com' and 'mycompany.org', both of which are the same, so each address at mycompany.com also exists at mycompany.org, and the emails go to the same people regardless of which domain is used, then you simply configure the domains in the ma…

How to 'share' domains between Exchange and VPOP3

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

How to 'share' domains between Exchange and VPOP3 If you want to have a VPOP3 server and Exchange Server using the same email domain, then you need to ensure that Exchange does not think it is 'authoritative' for the domain in question. See for details of how to do this in Exchange 2000 and 2003 (a similar process may be used in later versions of Exchange - contact your Microsoft Support technician if you need more help).

Configuring iCal on Mac OSX to connect to VPOP3's CalDAV service

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Configuring iCal on Mac OSX to connect to VPOP3's CalDAV service This requires VPOP3 v6 or later. The following instructions are for Mac OS X v10.7.5 but should work with similar versions. We have not been able to create an account by going to System Preferences

How to Install VPOP3

Anonymous (anonymous@undisclosed.example.com) — 2021-03-08T10:48:40+00:00

How to Install VPOP3 Simply download VPOP3 from the website, and run the installation program and follow the prompts. Occasionally people may have problems with the PostgreSQL part of the installation. If that happens, please contact us either by email at support@pscs.co.uk or by phone to +44 (0)1484 855800, and we will do our best to help.

Installation checklist

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Installation checklist This list contains some things you may want to check before or after installing VPOP3 to make sure it's not going to encounter any common issues. Before installation * Make sure that VPOP3 is not installed on a RAID 5 or RAID 6 array.

Installation Errors

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Installation Errors This page lists some errors which may occur during installation and the solution. In general, do NOT 'ignore' any errors unless we tell you to. If you have to retry an installation, when it is an upgrade from versions 1 - 4 going to version 5 or later, then make sure you have told the installer to install the database. Sometimes a partial installation will make the installer think that the database is already installed.

Internet Explorer 10 Issues

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Internet Explorer 10 Issues If you are using IE10 with VPOP3 prior to v6.2, then you may have issues accessing the VPOP3 Webmail and/or admin settings. These can usually be solved by telling IE10 to use 'compatibility mode'. Alternatively, using another web browsers such as

Setting up an iPhone/iPad/iPod Touch

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Setting up an iPhone/iPad/iPod Touch To set up an iPhone to access VPOP3's mail, you first of all need to configure VPOP3 to allow access by remote users (unless you will only be using the iPhone in the office, connected via WiFi to the office LAN). Adding the mail account to your iPhone/iPad

ISP needs SSL connection

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

ISP needs SSL connection A few ISPs use a non-standard and not recommended system of encrypting connections to their SMTP mail servers. These generally are called 'SSL' connections and work on an alternate port other than the standard SMTP port 25. (The correct way to encrypt connections is to use a system called TLS which works on the standard SMTP port).

How To: Move VPOP3

Anonymous (anonymous@undisclosed.example.com) — 2019-11-12T16:09:34+00:00

How To: Move VPOP3 You can usually move VPOP3 without having to uninstall and reinstall. It is best to move VPOP3 rather than reinstalling from scratch on the new PC or in the new location, because that way you can keep all your existing settings, rather than having to try to recreate them.

How to configure Mozilla Thunderbird

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

How to configure Mozilla Thunderbird This article won't show you all the possible settings in Thunderbird, because there are so many. Thunderbird is one of the most powerful & flexible email clients available at the time of writing, especially if you use IMAP4 (with VPOP3 Enterprise).

Outlook/Windows Messaging reports "No transport provider is available"

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Outlook/Windows Messaging reports "No transport provider is available" If Outlook or Windows Messaging reports No transport provider is available when trying to connect to VPOP3, it can mean several things. (This must be a contender for “the world's most meaningless error message

Outbound Messages Not Appearing in Monitor Target Mailbox

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Outbound Messages Not Appearing in Monitor Target Mailbox For VPOP3 to monitor outbound messages it needs to be able to work out that the message is FROM: a user whose mail should be monitored. To do this it has to examine the FROM: address in the message header.

How to configure Outlook 2007

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

How to configure Outlook 2007 Email SMTP Authentication To set up SMTP authentication in Outlook 2007, if your VPOP3 requires it, go to Tools -> Account Settings, select your email account and press Change.... Then, press the More Settings... button

How to configure Outlook 2010

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

How to configure Outlook 2010 In many ways, configuring Outlook 2010 is a similar to configuring Outlook 2007. The biggest difference you are likely to notice is the new “Ribbon” interface, in place of the traditional menu bar (File, Edit, View, etc.) Email

VPOP3 - POP3 Client Connection Problem

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

VPOP3 - POP3 Client Connection Problem These errors occur during the period when VPOP3 is trying to establish a connection to your ISP's POP3 mail server to receive incoming mail. They can mean that you have entered the POP3 Server address incorrectly, or that there is a problem with the network, or that your ISP's mail server is not working properly.

VPOP3 - POP3 Client Problem

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

VPOP3 - POP3 Client Problem These errors occur whilst VPOP3 is communicating with your ISP's POP3 mail server to retrieve your mail. The server connection was closed unexpectedly If the message text is Error with Pop3 Client (XXXX (YY)) The server connection was closed unexpectedly

Repairing corrupted database

Anonymous (anonymous@undisclosed.example.com) — 2026-06-05T07:26:39+00:00

Repairing corrupted database With PostgreSQL (as with most high-end databases) the database system will automatically recover after power failures etc, if it can. If it can't then there is no manual 'repair' function, because the data cannot totally be recovered (or it would automatically have been recovered).

How to Restore a backup of VPOP3

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

How to Restore a backup of VPOP3 The instructions below are to restore a full backup. You may also be able to recover deleted messages if you do not need to restore a full backup. Version 5 or later If you just need to restore a database backup, see steps 4 to 7 below.

Seeing where a message came from

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Seeing where a message came from Sometimes you need to check to see where a message really came from. The 'From:' email address is easily forged, so that cannot be relied upon. The first thing you have to do is to get the full message headers. These may look daunting, but are very useful for problem diagnosis.

Sender Policy Framework / SPF

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Sender Policy Framework / SPF SPF is a system used to tell mail servers which IP addresses can send mail from which domains. It is designed to reduce 'spoofing' of email addresses. For instance, if you receive an email message from your bank, your mail software can check that it came from an IP address authorised to send mail from your bank, and treat the message with suspicion if it didn't come from an authorised IP address.

Sending mail through your Gmail account

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Sending mail through your Gmail account According to Google, the settings for sending mail through Gmail are: Outgoing Mail (SMTP) Server - requires TLS or SSL: smtp.gmail.com (use authentication) Use Authentication: Yes Port for TLS/STARTTLS: 587 Port for SSL: 465

Setting up VPOP3 to work with Microsoft Exchange

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Setting up VPOP3 to work with Microsoft Exchange * Exchange 2003 * Exchange 2007 * Using advanced VPOP3 features with Exchange (eg monitoring, etc) * Using VPOP3 Spam Filtering with Exchange * How to 'share' domains between Exchange and VPOP3 Note that the VPOP3 settings are identical whichever version of Exchange you are using (5.5, 2000, 2003, 2007, 2010 or any later version), but the relevant settings in Exchange may move or be renamed between versions. If you are using a differe…

VPOP3 - SMTP Client Connection Problem

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

VPOP3 - SMTP Client Connection Problem These errors occur during the period when VPOP3 is trying to establish a connection to your ISP's SMTP mail server to send outgoing mail. They can mean that you have entered the SMTP Server address incorrectly, or that there is a problem with the network, or that your ISP's mail server is not working properly.

VPOP3 - SMTP Client Problem

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

VPOP3 - SMTP Client Problem These errors occur whilst VPOP3 is communicating with your ISP's SMTP mail server to send your mail. If the message text is: Error with SMTP Client (XXXX (YY)) The server connection was closed unexpectedly Then this means that the the connection between VPOP3 and your ISP's SMTP mail server was closed when VPOP3 did not expect it to be. This can be caused by the network connection failing or a bug in the ISP's mail server which drops the connection in abnormal circ…

How to start VPOP3

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

How to start VPOP3 There are two ways to start VPOP3 * as a service * as a normal application For normal operation, you will start VPOP3 as a service, as this means that VPOP3 will run even when no one is logged into the PC. To help with some types of problem diagnosis it can be better to start it as an application. This makes VPOP3 run in the account of the currently logged in user, rather than the service account, so it can eliminate access permission problems. Also, when VPOP3 starts a…

How To Move VPOP3 Version 2 to a New PC

Anonymous (anonymous@undisclosed.example.com) — 2019-11-12T16:06:44+00:00

How To Move VPOP3 Version 2 to a New PC (Also applies to version 1.x) To move VPOP3 to a new PC you should go through the following steps: * Copy the VPOP3 files * Copy the VPOP3 directory and subdirectories from the old PC to the new PC. (If you are moving to Windows Vista/2008/7/2012/8 or later, do NOT copy the files to a 'Program Files' folder on the new PC. Recent versions of Windows have special protection for those folders, which is not compatible with VPOP3)

How to move VPOP3 V3 to a new folder

Anonymous (anonymous@undisclosed.example.com) — 2018-12-05T15:25:41+00:00

How to move VPOP3 V3 to a new folder This guide assumes you want to move the whole of VPOP3 (including the message store) to a new folder on the same PC * Stop VPOP3 * Stop PostgreSQL * Remove the PostgreSQL service * Move VPOP3 to the new folder

VPOP3 Antivirus Update Error - Error 11

Anonymous (anonymous@undisclosed.example.com) — 2025-10-06T15:24:19+00:00

VPOP3 Antivirus Update Error - Error 11 If you receive an “Error 11” when VPOP3 Antivirus is attempting to upgrade, then this means that it cannot download the antivirus updates from the Internet * Make sure you are using the latest version of the VPOP3AV plugin. You can check the version in the Settings

VPOP3 Status Monitor Problems

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

VPOP3 Status Monitor Problems The VPOP3 Status Monitor is the program which shows the little (usually red) postbox icon in the Windows task tray. This usually launches automatically from the Windows startup group. This program is VPOP3Status.EXE on the disk, or can be run manually from

Message Archive -> General

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Message Archive -> General Settings -> Message Archive -> General Tab Archive Messages If the Archive Messages box is checked, then VPOP3 will archive incoming and outgoing messages. Main Archive Store Directory You can set the message archive store to any directory accessible by the VPOP3 service. Enter the path in the

Download Rules

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Download Rules Download rules are a facility in VPOP3 where it can look at message summary information before downloading a message from an ISP POP3 mailbox (they do not work on incoming SMTP messages - use SMTP Rules for that) To edit download rules, go to

Incoming SMTP Mail

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Incoming SMTP Mail If you have an incoming SMTP mail feed, then the mail server sending mail to you will connect to your VPOP3 computer to send the mail. The mail connection is controlled by the sending computer. IMPORTANT If you have a permanent Internet connection with a static IP address, the usual way of having incoming SMTP is to configure your

LAN Forwarding Queue Status

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

LAN Forwarding Queue Status To view the LAN Forwarding Queue Status, go to Settings -> Local Mail -> LAN Forwarding -> Queue Status The LAN Forwarding Queue shows the messages which VPOP3 has currently got queued to be sent to another mail server on your network using SMTP. The LAN Forwarding Queue status page shows a simple list of the messages waiting to be sent. The four columns in the table show:

Lists

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Lists The Lists section in VPOP3 lets you view and manage the various types of 'List' which VPOP3 supports * Distribution Lists * Mailing Lists * Forwardings * ODBC Mailing Lists * Groups Using a list A list will contain zero or more 'members' (usually email addresses) which can be messaged all at once. To send a message to all the members of a list, you will usually send an email to the listname at a valid domain.

ListServer Commands

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

ListServer Commands The ListServer is an automated process in VPOP3 which manages mailing lists. People can send commands to the ListServer to perform various functions remotely. Whether these commands are allowed, and exactly how they work depends on the particular mailing list's settings.

End()

Anonymous (anonymous@undisclosed.example.com) — 2026-05-29T10:39:35+00:00

End() End() This function is called by VPOP3 when the SMTP service session ends SMTP Server Lua Scripting The SMTP Server Lua Script is called SMTPSVR.LUA and can be edited from the Settings -> Scripts page in the VPOP3 settings. This script is called whenever an instance of the VPOP3 SMTP server is launched - ie whenever someone opens a connection to port 25 on the VPOP3 server to send it a message, whether from a local user or an incoming SMTP message.

Mail Collectors

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Mail Collectors A Mail Collector is how you tell VPOP3 to collect incoming mail. Each Mail Collector is associated with one or more Connections. The VPOP3 Connector Schedule determines when each Connection is run. Mail Collector General Tab Each Mail Collector has a General

Mappings

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Mappings In VPOP3, Mappings are a way of explicitly linking an email address to a user or list. They can also be used to indicate that an email address is remote, even though it would otherwise appear to be a local email address. In other email servers, a similar feature may be called 'aliases'

Misc -> Advanced Tab

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Misc -> Advanced Tab Settings -> Misc Settings -> Advanced You will normally not need to change any settings on this page unless VPOP3 technical support have suggested it. If you do make changes, and want to go back to the original settings, the Restore Defaults button will restore the settings to their defaults.

Misc -> DNS Tab

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Misc -> DNS Tab Settings -> Misc Settings -> DNS The DNS tab lets you specify which DNS servers VPOP3 will use. DNS (Domain Name System) is a system which converts Internet host names (eg www.google.com) into a numeric IP address (eg 1.2.3.4), because all connections on the Internet are actually performed using numeric IP addresses, but it is easier for people to remember names.

Misc -> External Fax Tab

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Misc -> External Fax Tab Settings -> Misc Settings -> External Fax The External Fax tab is for use with some external fax server applications which work by collecting mail from a POP3 mailbox. If a Fax Server Mailbox is selected, then VPOP3 will automatically send any locally sent mail to that mailbox if the recipient is local, but doesn't match another local address (a user, list, mapping etc),

Misc -> General Tab

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Misc -> General Tab VPOP3 Host Name The VPOP3 Host Name is used by VPOP3 when it is telling other mail software what it is called. For instance, when it connects to another SMTP server it will send the host name as the parameter for the HELO or EHLO command, and when an SMTP client connects to VPOP3, it announces its name in the welcome banner as required by the SMTP standard.

Reports

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Reports The Reports tab lets you access various reports about VPOP3 or message history. For many of reports to work, you need to have previously enabled historical logging. The currently available reports are listed below. To view a report, click on its name at the left of the page

Mail Sender Advanced Relay Settings

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Mail Sender Advanced Relay Settings SMTP Return Address The SMTP Return Address (or Return Path) is a hidden part of a message which says where bounce messages (and other automated responses) should be sent. (It is not the same as the Reply address

Mail Sender Advanced Settings

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Mail Sender Advanced Settings Mail Connectors -> Mail Senders -> (name) -> Advanced Advanced Domain Filtering For VPOP3 v6.11 and later, see the Domain Filtering section of the user manual. The Domain Filtering box lets you restrict which email messages are sent via this Mail Sender. You specify each rule on a separate line, and the message will be sent if it matches any sender rule

Spamfilter Script Configuration tab

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Spamfilter Script Configuration tab You reach this tab by going to Settings --> Spam Filter -> General, and then choose the General tab. The Spamfilter script has various settings that can be changed to alter the behaviour of the spamfilter. These are defined in the script, so may change with different versions of the script. The settings are currently:

Permissions

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Permissions This section lets you configure the permissions that a particular user has. Allowed Protocols The Allowed Protocols section lets you specify which services this user has access to. Note that these settings affect access to the whole service. If you want users to be able to access a service from some IP addresses, but not from others, then use the

Prune Rules

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Prune Rules The Edit User -> Prune Rules tab can be used to create/edit rules which cause messages to be automatically deleted according to specified criteria. To add or edit a “prune rule”, press the Add Rule button. This will add a new rule to the table, with a set of default settings. Don't worry, this rule doesn't take effect until you press the Submit button.

Webmail -> Advanced tab

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

Webmail -> Advanced tab This page is reached from Services -> Webmail Server, then the Advanced tab. Here you can set various options for the VPOP3 Webmail/settings service. Allow Password in URL If you check this option, then you can specify the user's password in a

What is IMAP4

Anonymous (anonymous@undisclosed.example.com) — 2018-11-14T10:45:49+00:00

What is IMAP4 IMAP4 (Internet Mail Access Protocol V4) is a new mail retrieval protocol which can be used as an alternative to the POP3 (Post Office Protocol V3). The main difference between IMAP4 and POP3 is that with POP3 the messages are only stored temporarily on the mail server until they are downloaded to the email client where the messages are stored, manipulated, searched etc. With IMAP4 the messages are stored permanently on the server, and they are manipulated, searched etc on the ma…

Welcome to your new DokuWiki

Anonymous (anonymous@undisclosed.example.com) — 2022-10-01T11:32:39+00:00

Welcome to your new DokuWiki Congratulations, your wiki is now up and running. Here are a few more tips to get you started. Enjoy your work with DokuWiki, -- the developers Create your first pages Your wiki needs to have a start page. As long as it doesn't exist, this link will be red: